Accounting of earthquake effect assumes that the structure resists passively through the combination of strength, deformation and energy absorption. The damping level of such a system is usually very low and therefore the energy dissipation value of such a system in elastic behavior is also low.During the strong earthquake the deformations of such structure will exceed the limits of elasticity and the structure will not collapse only due to its ability to deform in an inelastic manner. Inelastic deformations take the form of localized plastic joints, which leads to increased pliability and energy absorption. Accounting this most of the earthquake energy is absorbed by the structure through local damages.

Let's consider the energy distribution in the structure. During the seismic effect a certain amount of energy is delivered to the structure. This energy is presented as kinetic and potential energy that must be absorbed or dissipated. If there is no damping in the structure, the oscillations will continue endlessly. However, the structure always has some damping characteristics and due to this the amplitude of oscillations decreases during the motion. It is possible to increase resistance of the structure to earthquake and reduce the number of damages by adding special damping elements to the structure. Such elements are integrated into the framework and absorb the energy that passes through them.

The law of conservation of energy of such system has the form:


where2.png - total energy under earthquake action,   

           3.png - total kinetic energy,  

           4.png- elastic deformation energy, 

           5.png - inelastic deformation energy, 

           6.png - energy dissipated in a special damping element.

LIRA-FEM allows you to take into account the work of special damping elements with the finite element of viscous damping (FE 62), whose scheme is shown in Fig. 1.


Fig. 1. Spring-damper system.

Let's consider the work of this element.

The energy loss in a single oscillation cycle in such an element can be defined as:


where7.png - damping force.

In the linear mathematical model, the viscous damping force8.png.

The equation of harmonic oscillations looks like


and the speed of movement is determined by the expression:


With the fact that7c.png, we can write down


Then the energy loss in one cycle of oscillation is equal to:


In resonance13.png, and14.png,


Equation (4) can be written as:


Damping force:


Expression (9) can be presented in the form:


The ellipse, defined by equation (10), can be represented graphically (Fig. 2).


Fig. 2. Energy dissipation in the viscous damper during the oscillations cycle.

Other mechanisms of energy dissipation can be represented as a viscous damper by equating the work per cycle, as it is done for a viscous damper.


Therefore, the equivalent damping factor is defined as:


Let's solve a test example of oscillation of two frames. The geometrical and physical characteristics are identical. Length of span - 5m, height of the floor - 3 m, section of columns - I-section 35K1, section of beams - I-section 30B1. The same dynamic load is applied to both frames. In one frame between the floors we shall install the elements of viscous damper (FE 62) as it is shown on figure 3.


Fig 3. Analytical model.

Characteristics of the viscous damper element are specified in the form (Fig. 4.),

Fig 4.png

Fig. 4. Dialog box.

Where 21.png element stiffness in axial direction (N/m), 22.png - viscous damping coefficient (N*s/m).

To calculate the damping factor22.pngwe will use the formula


Damping degree24.png - dimensionless ratio of damping factor to critical damping:


The nature of the movement depending on the value of the degree of damping can be divided into three cases:

  • 24.png< 1,0oscillatory motion;
  • 24.png> 1,0 non-oscillatory motion;
  • 24.png= 1,0 critical damping motion.

Lets consider the problem of damping degree influence. For three frames with FE 62 (Fig. 5.) we will set different parameters of24.png.


Fig. 5. Analytical model.

26.png 27.png28.png

There are various mechanisms that can cause attenuation in the structure. LIRA-FEM has a special FE, which simulates the operation of the linear element of the viscous damper. In this element, the damping force is proportional to the speed. In many cases such a simple expression for damping force is impossible. However, it is possible to obtain an equivalent viscous damper factor. For this purpose it is necessary to equate the loss of kinetic and potential energy with the dissipation energy.

If you find a mistake and want to inform us about it, select the mistake, then hold down the CTRL key and click ENTER.

  • 1.1K

Богдан Писаревский

Инженер-программист компании «ЛИРА САПР».
Разработка программных комплексов.

More publications of the author

Анатолий Пикуль

Инженер-аналитик компании «ЛИРА САПР».
Ассистент кафедры металлических и деревянных конструкций Киевского национального университета строительства и архитектуры

More publications of the author